Shelf status: last synced Nov 13, 1:33 PM ET. The supplier feed is temporarily unavailable, so sizes and prices shown come from that last successful sync. Call to confirm before you drive: shop (954) 760-7276 (Mon–Fri 8–5, Sat 8–2) · 24-hour line (561) 971-9869.
FLATFIXVAULT
Tools ▾
Call the shop (954) 760-7276

Tires › Tire guides

Tire sidewall explained

FlatFixVault tire guide · Published 2026-10-24

A tire sidewall is a label molded into rubber. It tells you the size, how much load the tire can carry, the maximum speed it is rated for, when it was made and what its treadwear grades are. Most of it is standardized, so the same markings mean the same thing on every brand. This guide walks through them in the order you usually find them.

Short answers

What is the largest string on a tire sidewall?

The size, such as 275/65R18: section width in millimeters, aspect ratio, radial construction and wheel diameter in inches.

What do the number and letter after the size mean?

The number is the load index, a code for the maximum load one tire can carry at the pressure on the sidewall; the letter is the speed symbol, a code for the maximum rated speed.

What do LT and ST in front of a size mean?

LT marks a light truck tire, built for heavier loads than a P tire with the same numbers; ST marks a trailer tire.

The size string

The largest string on the sidewall is the size. On a passenger tire it looks like 275/65R18: section width in millimeters, aspect ratio, radial construction and wheel diameter in inches. Light truck sizes often begin with LT, and trailer sizes with ST. Some sizes are written in inches instead, such as 35x12.50R20, and commercial tires use sizes like 245/70R19.5.

The letter in front matters. An LT tire is built for heavier loads than a P tire with the same numbers, and the two are not interchangeable by default. Our guide on reading a tire size explains each part in more detail.

Load index and speed symbol

After the size you normally see a number and a letter, for example 116T. The number is the load index: a code for the maximum load one tire can carry when it is inflated to the pressure printed on the sidewall. The letter is the speed symbol, a code for the maximum speed the tire is rated for. Higher is not automatically better; the replacement should meet what the vehicle maker specifies.

Some tires show a load range instead, such as Load Range E, which is common on light truck and commercial tires. That is a different scale from the load index and describes the tire's construction and inflation range.

The DOT code and the date

Look for the letters DOT. The characters after it identify the plant and the tire line, and the last four digits give the week and year of manufacture. 2421 means week 24 of 2021. Tires made before 2000 used three digits, and you may still see those on very old stock; they are read differently and are a reason to have the tire inspected.

The scanner reads the DOT code from a photo and shows the week, the year and the age in years and months. You can also type the four digits into our DOT decoder if the photo will not focus.

UTQG: treadwear, traction and temperature

Many passenger tires carry a UTQG line: TREADWEAR 500 TRACTION A TEMPERATURE A. Treadwear is a comparative number assigned by the manufacturer, not a mileage promise. Traction grades wet braking on a government test, and temperature grades resistance to heat buildup. The grades are only comparable within the same manufacturer's line, so use them as one input, not a ranking.

Maximum load and pressure

A line such as MAX LOAD 1200 LBS AT 44 PSI states the tire's maximum load and the pressure at which that load is rated. This is not the pressure you should run day to day. The correct pressure for your vehicle is on the driver-door placard and in the owner's manual. Filling to the sidewall maximum commonly leaves tires overinflated.

M+S, 3PMSF, XL and other marks

M+S means the tire was designed for mud and snow. 3PMSF (often shown as a three-peak mountain snowflake symbol) indicates a tire that meets a specific snow-traction test; it is a stronger claim than M+S alone. XL or Extra Load means the tire is built to carry more load at a higher pressure than the standard version of the same size. RADIAL and TUBELESS describe construction and whether an inner tube is used.

What the sidewall cannot tell you

The sidewall describes the tire, but it cannot show you what is happening inside it. Cracks, bulges, a puncture in the shoulder, or damage from running low on air may not be visible in the markings at all. A DOT date also does not by itself prove a tire is safe or unsafe; age is one factor and the tire still needs to be inspected for cracks, bulges, cuts and uneven wear.

If anything on the sidewall is unreadable, or you are not sure which number is the size, scan it or type what you can see. The scanner marks each field as confirmed, probable or unreadable and asks you to confirm when two readings disagree.

Scan this tire with your phone

Point your phone at the sidewall and Tire Scan reads the size, the DOT week and year, the load and speed markings and the UTQG grades. It runs on your phone; the photo stays there unless you choose to send a small crop to help improve the scanner.

Questions about your tires?

Call the shop at 954-760-7276 (Monday to Friday 8 AM to 5 PM, Saturday 8 AM to 2 PM, closed Sunday) or text 561-971-9869 with your tire size or a photo of the damage. Prices are quoted by phone.

Bring it in

Walk in at FlatFixVault, 1919 NW 19th St, Suite 204, Fort Lauderdale FL 33311. Shop hours are Monday to Friday 8 AM to 5 PM and Saturday 8 AM to 2 PM; closed Sunday. No appointment needed, or call the shop first at 954-760-7276.

We sell new tires only and do installation, balancing, flat repair and air fills. We do not do alignments.

Related

QR code to leave a Google reviewBought from us? Leave a Google review. It helps other drivers find us.